ModbusRtu/10/params/
Parameters for Grid off inverter INVSOL01
8.10.2023*16:58:45
Protocol:Rtu
Description:Protocol for INVSOL01 Modbus RTU 1.04.15 Machine info
Device:INVSOL01,USB-RS485
Port:Com,5,19200,8,1,0
Timing:Timer=10,Sleep=10,Wait=200,Timeout=5
Device Address:04
Commands:19
001:0x03,0x4E,0x86,0x00,0x01/1,0,99999,1.0/U,Inverter output voltage Set 220.0V-240.0V;(2200-2400);Set the output voltage amplitude.
002:0x03,0x4E,0x87,0x00,0x01/1,0,99999,1.0/U,Inverter output frequency Set 50.00Hz/60.00Hz;5000/6000;Set the output frequency.
003:0x03,0x4E,0x88,0x00,0x01/1,0,99999,1.0/U,Inverter search mode enable 0:OFF 1:ON  ;"effective range:0,1 the default value is 0;";0:If disabled, no matter connect load is low or high, the on/off status of inverter output will not be effected, 1:If enable, the inverter begins search mode if the 
004:0x03,0x4E,0x8C,0x00,0x01/1,0,99999,1.0/U,Inverter discharger to grid enable "48V:   0:OFF  1:ON  24V:  Null";"effective range:0,1 the default value is 1;";1:Enable Inveter discharging from battery to grid when the Inverter is connnectted to Grid 0:Disable  Inveter discharging from battery  to
005:0x03,0x4E,0x8D,0x00,0x01/1,0,99999,1.0/U,Energy use mode "48V:1:SBU;2:SUB;3:UTI;4:SOL (for PV;PH)1:BAU; 3:UTI;4:BOU (for EP)12V 24V:1:SBU;;3:UTI;4:SOL (for PV;PH)1:BU; 3:UTI (for EP)";;refer to user's manual
006:0x03,0x4E,0x8F,0x00,0x01/1,0,99999,1.0/U,Grid protect standard "0:VDE4105; 1:UPS  ;  2:home ;3:GEN";;refer to user's manual
007:0x03,0x4E,0x90,0x00,0x01/1,0,99999,1.0/U,SolarUse Aim "0:LBU  1:BLU(defalut)(for PV;PH)0:LB  1:LU(defalut)  (for EP)";;
008:0x03,0x4E,0x91,0x00,0x01/1,0,99999,1.0/U,Inverter max discharger current "48V:  0.1A(AC)12V 24V:  Null";1.0A-21.7A(10-217);Set the max discharging current from Inverter
009:0x03,0x4E,0x96,0x00,0x01/1,0,99999,1.0/U,Battery stop discharging voltage 0.1V  ;440~580(44.0-58.0)V the default value is 46.0V;refer to user's manual
010:0x03,0x4E,0x97,0x00,0x01/1,0,99999,1.0/U,Battery stop charging voltage 0.1V  ;440~580(44.0-58.0)V the default value is 54.0V;refer to user's manual
011:0x03,0x4E,0x9D,0x00,0x01/1,0,99999,1.0/U,Grid max charger current set 0.1A(DC);10~800(1.0-80.0)A the default value is 60.0A;
012:0x03,0x4E,0x9F,0x00,0x01/1,0,99999,1.0/U,Battery low voltage 0.1V;400~480(40.0-48.0)V the default value is 40.8V;
013:0x03,0x4E,0xA0,0x00,0x01/1,0,99999,1.0/U,Battery high voltage 0.1V;580~600(58.0-60.0)V the default value is 60.0V;
014:0x03,0x4E,0xA4,0x00,0x01/1,0,99999,1.0/U,Max Combine charger current "0.1A(DC)(for PV;PH)";10~1400(1.0-140.0)A the default value is 60.0A;
015:0x03,0x4E,0xAE,0x00,0x01/1,0,99999,1.0/U,System setting ;refer to the frame System setting bit;
016:0x03,0x4E,0xAF,0x00,0x01/1,0,99999,1.0/U,Charger source priority "0:Soalr first  (for PV;PH)2:Solar and Utility(default)  (for PV;PH)3:Only Solar  (for PV;PH)2:Utility charger enable (default)  (for EP)3:Utility charger disable   (for EP)";;
017:0x03,0x4E,0xB0,0x00,0x01/1,0,99999,1.0/U,Solar power balance "0:SBD 1:SBE";;
018:0x03,0x4E,0xF5,0x00,0x01/1,0,99999,1.0/U,Remove the accumulated data 0:No remove the accumulated data 1:Remove the accumulated data;" the default value is 0; effective range:0,1";
019:0x03,0x4E,0xF6,0x00,0x01/1,0,99999,1.0/U,Reset the parameter 0:No effect 1:Action ;" the default value is 0; effective range:0,1";
end